Wax

• Leather, fabric, combination or padded gloves
• (for fleece gloves, use Nikwax Polar Proof)

• Adds water repellency
• Prolongs life and performance of all leather and fabric gloves
• Ideal for gloves with breathable membranes e.g. Gore-Tex
• Maintains breathability
• Maintains palm grip
• Conditions leather replacing tanning agents in leather gloves
• Can be applied to wet or dry gloves
• Easy to apply - can be used indoors unlike solvent sprays
• WaterBased - environmentally friendly, biodegradable, non flammable, non hazardous
• Does not contain fluorocarbons
• Guaranteed performance for 4 years from manufacture

LF10X YELLOW, 0°C/10°C, 180G

Temperature range from 0°C to 10°C (32°F to 50°F). Recommended iron temp.: 120°C (248°F). LF10X is made a little bit harder than the old LF10. Our test result shows that a slightly harder wax performs better in this area, especially noticeable when used alone. The adjusted hardness is also making the wax more durable than before. It’s a good wax for base prep wax, but also a great training wax. For racing we recommend to go with high fluoro wax in this temperature area, but with a powder on top LF10X can be used with a good result. The FC10X powder would then be the natural choice. The speed of the iron should be approx. 8-10 sec. on a snowboard or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax.

High fluoro waxes are known for achieving ultimate speed and the best performance.  Considered the "Holy Grail" of race waxes, this product is an essential component of any racer's wax lot. Unlike other HF waxes, ours contains minimal dye and additives, is environmentally friendly, and uses a classified non-hazardous blend. 

Contains high flouro to give optimal glide in high humidity snow. These waxes are a must for race day.

Non Fouro Wax

-12C and Below

I84 CLEANER,FLUORO GLIDEWAX,70ML

Cleaner for fluoro glide wax and CH wax. Improves glide and conditions the base. For glide sections only on all racing skis and snowboards. Involves no hard mechanical treatment of the base. No wearing of the stone grind pattern in the ski base. Makes the ski faster! Apply cleaner (I84) with Fiberlene. Brush with white nylon brush while wet. Wipe clean with Fiberlene. Let dry for 5-30 minutes. Brush with hand steel brush (or Roto steel brush). Wax with Base Prep wax. 2.5 fl. oz.

FC6AC CERA F ROCKET SPR+2/-10C 70ML

Liquid fluorocarbon topping for colder conditions +2°C to -10°C (36°F to 14°F). Rocket Cold works best when high humidity. Used on top of Cera F powder or mixed with the powder. Can also be used on top of HFX and LFX waxes with good results. Less expensive than HVC®. Danger. Extremely flammable aerosol. Pressurized container: May burst if heated. Causes skin irritation. Causes serious eye irritation. May cause respiratory irritation.

Racing performance

Cera F liquid topping +2°C to -10°C. For active skiers and waxers. Gives superior glide.

FC6XS CERA F SOLID 2°C/-15°C, 20G

100% fluorocarbon solid block of wax. For transformed/man made snow, +2°C to -15°C. Used alone or as the final “accelerator” layer. Applied with roto or hand cork for sufficient friction heat. Can also be ironed. Simple and easy application for alpine runs, snowboards, junior racing, sprints etc.

Racing performance

Cera F Cold Turbo block topping +2°C to -15°C. For cold humid conditions. Easy to apply.

LF7X VIOLET, -2°C/-8°C, 60G

Temperature range from -2°C to -8°C (28°F to 18°F). Recommended iron temp.: 140°C (284°F). LF07X performs great in normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end-result. Can be used as a racing wax at low air humidity, but will also serve the purpose as a brilliant training wax. The speed of the iron should be approx. 8-10 sec. on a skating ski or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. When used as a base for Cera F, we recommend the new FC07X powder.

Future Cera

The LFX series is great gliders for training and competition with very good glide properties.

LF8X RED, -4°C/4°C, 60G

Temperature range from -4°C to 4°C (25°F to 39°F). Recommended iron temp.: 130°C (266°F). A continuation of the std. LF8, a great wax for both base-prep and training. It can also can be used as a race wax, preferably with Cera F powder on top. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a snowboard or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. When used as a base for Cera F, we recommend the FC08X powder.

Future Cera

The LFX series is great gliders for training and competition with very good glide properties.

LF7X VIOLET, -2 °C/-8°C, 180G

Temperature range from -2°C to -8°C (28°F to 18°F). Recommended iron temp.: 140°C (284°F). LF07X performs great in normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end-result. Can be used as a racing wax at low air humidity, but will also serve the purpose as a brilliant training wax. The speed of the iron should be approx. 8-10 sec. on a skating ski or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. When used as a base for Cera F, we recommend the new FC07X powder.

Future Cera

The LFX series is great gliders for training and competition with very good glide properties.

LF8X RED, -4°C/4°C, 180G

Temperature range from -4°C to 4°C (25°F to 39°F). Recommended iron temp.: 130°C (266°F). A continuation of the std. LF8, a great wax for both base-prep and training. It can also can be used as a race wax, preferably with Cera F powder on top. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. When used as a base for Cera F, we recommend the FC08X powder.

Future Cera

The LFX series is great gliders for training and competition with very good glide properties.

UR8 RED BIO RACING WAX, 180G

Red alpine wax, -12°C to +2°C (12°F to 36°F). Bio degradable. For all snowtypes.

UR waxes are fluor free

Excellent for training and competition.

UR6 BLUE BIO RACING WAX, 180G

Blue alpine wax for cold conditions, -10°C to -20°C (14°F to -4°F). Bio degradable. For all snowtypes.

Fluor Free

UR waxes are fluor free, but excellent for training and competition.

CH7X VIOLET, -2 °C/-8°C, 180G

Temperature range from -2°C to -8°C (28°F to 18°F). Recommended iron temp.: 140°C (284°F). A wax that performs great in normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end-result. CH07X is an economic training and racing wax as well as an all round base prep wax. The speed of the iron should be approx. 8-10 sec. on a snowboard or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax.

Fluoro Free

Hydrocarbon wax -2°C to -8°C. Good training wax. Easy to warm in. Good in dry conditions.

For winter snow that’s on the warmer side of the spectrum, wax your skis or board with Wend NF Performance Warm. This bulk wax has a bit of Wend’s famous MeadowFoam component, a botanical oil extracted from flowers. MeadowFoam helps the wax penetrate and adhere to your bases for a smoother ride and longer durability. This soft wax has a low melting point and is easy to work with.

• Non fluorinated wax for skis and snowboards
• Warm formula, for temperatures above 28F (-2C)
• 100g bulk bar (3.5oz)
• Set wax iron to 140F (60C)
• Contains MeadowFoam oil

Treat your skis to a performance wax with MeadowFoam, when you use Wend NF Universal Wax. This is softer than many universal waxes, and with the addition of MeadowFoam, it penetrates and conditions the base of your skis or snowboard with ease.

• Universal non fluoro wax for skis and snowboards
• Best when snow is between 10F – 40F (-12C to 4C)
• 100g bulk bar (3.5 oz.)
• Set wax iron to 140F – 167F (30C to 40C)
• Contains botanical MeadowFoam oil

WEND Performance Base Prep Saturation/Conditioning 100g

Hot Iron

Hydrocarbon, no additives, the best value in the industry!

• Warm = 32F to 26F (0C to -3C) 165g

 High fluoro glide wax -2⁰C to -8⁰C. For fresh,old or man made snow. Good in clean snow. Easy to apply.

F4-100C GLIDEWAX LIQUID 100ML

F4 Universal All Temperature Liquid wax. For all skis and snowboards. All snow conditions. With foam applicator and felt polisher. Handy ergonomic pocket size. Apply, polish and go! Based upon Future Cera® raw materials, which grant for high quality and an environmentally friendly profile. Danger: Highly flammable liquid and vapour. Causes serious eye irritation. May cause drowsiness or dizziness.

 SWIX F4 Universal Glide Wax is a high quality water-repellent fluoro paste wax for skis and snowboards. It's a handy pocket size and perfect for any snow condition, apply it and go!

HANDY WHEN TRAVELLING AND ON THE GO

HF10X YELLOW, 0°C/10°C, 40G

Temperature range from 0°C to 10°C (32°F to 50°F). Recommended iron temp.: 120°C (248°F). HF10X is made a little bit harder than the old HF10. Our test result shows that a slightly harder wax performs better in this area compared to the old classic, especially noticeable when used alone. The adjusted hardness is also making the wax more durable than before. The speed of the iron should be approx. 8-10 sec. on a snowboard/ ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. HF10X can be used as a race wax alone, but is often used as a base for Cera F, such as FC10X and HVC Warm.